- 相關推薦
直流無刷稀土永磁電動機調速系統的設計
直流無刷稀土永磁電動機調速系統的設計 【直流無刷稀土永磁電動機調速系統的設計】相關文章： 基于DSP的網絡化無刷直流電動機控制系統09-17 直流雙閉環可逆調速系統研究10-10 雙閉環直流調速系統的工作原理(一)08-21 基于VC++串行通信的無刷直流電機監控系統07-26 共用直流母線變頻調速系統在滌綸短絲線上的應用10-27 基于PLC的電機調速系統設計08-07 探討變頻調速異步電動機的設計要點10-14 應用于光伏水泵系統中的無位置傳感器無刷直流電機的控制10-04
摘 要：無刷直流電動機 (BLDCM)因為具有良好的性能、控制方便和高的性價比等優點，所以一直得到很廣泛的應用。本文介紹了永磁無刷直流電動機速度控制的一種方案，及當前無刷直流電動機控制的發展趨勢和常見的新型控制方法。最后采用端電壓過零檢測法和預定位起動方法，實現了基于 TMS320F240 DSP的無位置傳感器永磁無刷直流電動機速度控制。
在系統的硬件設計中，設計了以TMS320F240數字信號處理器為核心處理器的最小系統。同時也設計了信號采集電路，用于測量控制系統所需的三個定子端電壓信號和相電流反饋信號。
在系統的軟件設計中，主要完成了電動機的起動及無傳感器速度閉環控制兩大功能。用DSP成功實現PWM輸出信號、信號采集及移相控制等功能。
關鍵詞：數字信號處理器（DSP）；無刷直流電動機；轉子位置傳感器；
反電動勢；速度控制The design of speed control system of Rare-earth Permanent Magnet Brushless DC Motor
Abstract：The Brushless DC Motor(BLDCM) has been widely used for many years because of its excellent performance, easy control and high cost effectiveness.This paper introduces the control of Brushless Permanent Magnet DC Motor ,and introduces the future of the control BLDCM; and some new methods in controlling DC motor. In the end, a complete solution proposal in the paper. It deals with sensor less alternative. To position sensors for speed control in Brushless Permanent Magnet Dc Motor based on TMS320F240,using the back-EMF. Commutation method and the start method by means of rotor pre-setting.
TMS320F240DSP has been designed as the main micro-controller during hardware design. Minimum system. Circuits for signal collection have been given to measure the stator terminal voltage and current value.
When designing the software, the main two functions, startup of the motor and speed closed loop sensor less control are complete. Using DSP, the PWM signal, the measurement of voltage and current signals and phase shifting are successively presented here.
Keywords： DSP(Digital Signal Processing); BLDCM(brushless direct current motor);Rotor Position Sensor; BEMF(Back Electromagnetic Force);Speed Control.